Close

Viega Prestabo Šeit ir 205 preces.

Prestabo

Press connector systems with press connectors and pipes made of non-​alloy steel 1.0308 (E235), in acc. with DIN EN 10305‑3, externally galvanised with a zinc layer thickness of 8–15 µm (blue chromatised). 

Press connectors 
All sizes with SC‑Contur – connections, which remain unpressed become visible when the system is filled. The S...

Prestabo

Press connector systems with press connectors and pipes made of non-​alloy steel 1.0308 (E235), in acc. with DIN EN 10305‑3, externally galvanised with a zinc layer thickness of 8–15 µm (blue chromatised). 

Press connectors 
All sizes with SC‑Contur – connections, which remain unpressed become visible when the system is filled. The SC‑Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage. 
During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa

Dimensions 
Standard sizes: d 12; 15; 18; 22; 28; 35; 42; 54 
XL sizes: d 64.0; 76.1; 88.9; 108.0 

Areas of application 
Heating systems 
Industrial and plant engineering 
Sprinkler units (sendzimir galvanised pipe) 
Compressed air units (sendzimir galvanised pipe) 
Solar installations with flat collectors 
Solar installations with vacuum collectors (only with FKM sealing element) 
Cooling water piping 

Use of the system for application areas and media other than those described here must be agreed with Viega Service Center. 

Operating conditions with EPDM sealing element 
  • Operating temperature max. 110 °C
  • Operating pressure max. 1.6 MPa (PN 16)

Use of press tools 
The functional safety of the Viega press connector systems is primarily dependent on the perfect condition of the press tools and press machines used. For this reason, for the production of press connections, we recommend the use of Viega press tools and their regular inspection by authorised service points. 

Technical data 
Press connectors and components are constantly being optimised. If required, the current Z and installation dimensions can be obtained from the download area of the Viega homepage: viega.com/downloads 

Protection against external corrosion 
Prestabo pipes and connectors are protected by external galvanisation. In case of contact with dampness (condensation, precipitation during the construction phase, plaster and splash water etc.) or corrosive building materials (surfacer, levelling screed etc.), however this layer of zinc cannot provide permanent protection against external corrosion. The following protective measures are recommended: 
  • Use of closed-​cell insulating tubes with professional sealing of all abutting and cut edges using a suitable filler.
  • Damp-​proofing of the laid pipe through separating foil in the floor construction.
  • Installing pipes outside areas at risk of moisture.
  • Visible radiator connections rising from the floors should be avoided if floors will be frequently cleaned with water and/or cleaning agents/disinfectants, for example in retirement homes and care homes as well as hospitals. Wall connections make cleaning easier and also exclude any additional risk of corrosion.
  • If the radiator connections do come from the floor, professional corrosion protection and professional sealing of the joints must be ensured. If not, there is a possibility that the cleaning water will penetrate, which will moisten the insulation and present the risk of corrosion.

If the measures in the examples above fail to provide permanent protection against dampness or the areas of use are connected with special requirements, e.g. in cooling circuits, complete external corrosion protection, which reliably prevents influences that lead to corrosion must be applied.
Vairāk
vienā lapā
Rāda 1 - 60 no 205 produktiem
Rāda 1 - 60 no 205 produktiem
Close